Tired of your Arrma Kraton’s sluggish performance and unreliable reception? It’s time to breathe new life into your RC vehicle by upgrading its receiver. A new receiver can drastically enhance your vehicle’s speed, responsiveness, and range, giving you an unparalleled driving experience. Whether you’re a novice or an experienced hobbyist, this guide will walk you through the simple steps of changing the receiver on your Arrma Kraton. Get ready to unleash the full potential of your RC car and conquer any terrain with precision and finesse!
Before embarking on this project, it’s crucial to gather the necessary tools and components. You’ll need a new receiver compatible with your Arrma Kraton, a soldering iron with solder, wire strippers, heat shrink tubing, and a small screwdriver. Once you have everything you need, find a well-lit and spacious area to work in. Remember, proper preparation ensures a successful outcome, so take your time and carefully follow each step.
Now that you’re all set, let’s dive into the process of changing the receiver. Begin by removing the body of your Arrma Kraton to expose the chassis. Locate the existing receiver and disconnect the wires connected to it. Note the position of each wire before removing it to ensure correct reconnection later. Once the old receiver is disconnected, remove it from the chassis. Now, take the new receiver and connect the wires to the corresponding channels on the receiver. Ensure the wires are securely connected and solder them for a strong bond. Cover the soldered connections with heat shrink tubing for added protection and insulation. Finally, securely mount the new receiver in the chassis and reattach the body. Power up your Arrma Kraton and test the receiver to confirm its functionality. Congratulations, you’ve successfully upgraded the receiver on your Arrma Kraton, unlocking a world of enhanced performance and reliability!
Waterproof Receivers
If you’re planning on running your Arrma Kraton in wet or muddy conditions, you’ll need to install a waterproof receiver. Waterproof receivers are designed to withstand immersion in water, and they’ll keep your Kraton running even if you get it wet. There are many different waterproof receivers on the market, so it’s important to do your research to find the one that’s right for you. Here are a few things to consider when choosing a waterproof receiver:
- Compatibility: Make sure the receiver you choose is compatible with your Arrma Kraton. Not all receivers are created equal, and some may not be able to handle the high-power output of a brushless motor.
- Range: Consider the range of the receiver you choose. If you’re planning on running your Kraton at long distances, you’ll need a receiver with a long range.
- Features: Some waterproof receivers come with additional features, such as telemetry or Bluetooth connectivity. If you’re looking for a receiver with specific features, be sure to do your research to find one that meets your needs.
Once you’ve chosen a waterproof receiver, you’ll need to install it in your Arrma Kraton. The installation process is relatively simple, but it’s important to follow the instructions carefully. Here are the steps involved in installing a waterproof receiver in an Arrma Kraton:
1. Disconnect the battery. Always disconnect the battery before working on your Arrma Kraton. This will prevent any electrical accidents from happening.
2. Remove the body. The body of the Arrma Kraton is held in place by four screws. Remove these screws and lift off the body.
3. Locate the receiver. The receiver is typically located in the center of the chassis. It’s a small, black box with a number of wires attached to it.
4. Disconnect the receiver wires. There are typically three wires connected to the receiver: the power wire, the ground wire, and the signal wire. Disconnect these wires by gently pulling them out of the receiver.
5. Connect the new receiver wires. Connect the wires from the new receiver to the corresponding wires on the Arrma Kraton. The power wire is typically red, the ground wire is typically black, and the signal wire is typically white.
6. Secure the receiver. Once the receiver wires are connected, you can secure the receiver in place using double-sided tape or Velcro.
7. Reinstall the body. Once the receiver is secure, you can reinstall the body.
8. Reconnect the battery. Reconnect the battery to the Arrma Kraton.
9. Test the receiver. Once the battery is connected, you can test the receiver by turning on the transmitter and receiver. The receiver should bind to the transmitter and the LED on the receiver should turn solid green.
If you’re having trouble installing the waterproof receiver, you can consult the Arrma Kraton manual or contact customer service for assistance.
17. Troubleshooting
If you’re having problems with your Arrma Kraton receiver, there are a few things you can try to troubleshoot the issue:
- Check the power connections. Make sure that the power wire from the receiver is securely connected to the battery. Also, check that the ground wire from the receiver is securely connected to the chassis.
- Check the signal connections. Make sure that the signal wire from the receiver is securely connected to the ESC. Also, check that the signal wire from the receiver is not damaged.
- Try a different receiver. If you’re still having problems, try replacing the receiver with a new one. This will help you determine if the receiver is the source of the problem.
If you’re still having problems with your Arrma Kraton receiver, you can contact customer service for assistance.
| Symptom | Possible Cause | Solution |
|---|---|---|
| No power to the receiver | Power wire not connected | Connect the power wire to the battery |
| No signal to the receiver | Signal wire not connected | Connect the signal wire to the ESC |
| Receiver not binding to the transmitter | Receiver not powered | Connect the power wire to the battery |
| Receiver not binding to the transmitter | Transmitter not powered | Connect the power wire to the transmitter |
| Receiver not binding to the transmitter | Transmitter and receiver not on the same frequency | Set the transmitter and receiver to the same frequency |
Receiver Binding Process
- Turn on the transmitter and receiver. Make sure that the transmitter is in "bind" mode. This is usually indicated by a flashing LED light on the transmitter.
- Hold the receiver close to the transmitter. The receiver should be within a few inches of the transmitter.
- Press and hold the bind button on the receiver. This button is usually located on the side of the receiver.
- Wait for the LED light on the receiver to turn solid. This indicates that the receiver is bound to the transmitter.
- Release the bind button on the receiver.
- Turn off the transmitter and receiver.
- Turn on the transmitter and receiver again. The receiver should now be bound to the transmitter and will respond to the transmitter’s controls.
Troubleshooting:
- If the LED light on the receiver does not turn solid, try the following:
- Make sure that the receiver is close enough to the transmitter.
- Make sure that the bind button on the receiver is being held down.
- Try replacing the batteries in the transmitter and receiver.
- If the receiver does not respond to the transmitter’s controls, try the following:
- Make sure that the receiver is bound to the transmitter.
- Check the connections between the receiver and the ESC.
- Check the connections between the ESC and the motor.
